Skip to the sign-up form
ENCZ – Česká verze stránkyJoin the list
Render: birch plywood sheet S02 on paprika-red paper in morning sun, the outlines of its parts pencilled on, a pencil and a grey Euro box beside it.

Furniture around Euro boxes

This sheet
is your
furniture.

Design it in minutes. Get it cut, put it together yourself.

Get on the list

Shuplo isn't on sale yet. Leave your email and we'll tell you when it is.

Preview renderSheet S02: birch plywood, 18 mm, nested by our software. A render, not a photo.

Render: a CNC router cutting the first outline of sheet S02, sawdust around the cutter, the rest of the path shown as a dashed line.

The cut

Every cut is drawn by software.

Our software writes every outline, hole and connector groove into the cutting files. The router follows them.

  • 8/8parts cut
  • 80/80holes
  • 42/42connector grooves

Preview renderSheet S02 · planned cutting order · render

Render: the cut parts of sheet S02 lifting out of the offcut, each casting its own shadow on green paper.

Out they come

Every part knows its place.

Each part comes off the sheet with its name and its step in the assembly manual. Point at one to see which it is.

Each part comes off the sheet with its name and its step in the assembly manual. Tap one to see which it is.

  • Vertical divider · CD-01: goes in at step 18
  • Left side · CS-01: goes in at step 13
  • Door · DR-01: goes in at step 42
  • Drawer front · DF-02: goes in at step 41
  • Right side · CS-02: goes in at step 23
  • Bottom · CB-01: goes in at step 13
  • Box shelf · SH-01: goes in at step 15
  • Drawer front · DF-01: goes in at step 39

Preview renderSheet S02 · 8 parts · render

Render: the cart's carcass lying on its back as in the assembly manual, the next part sliding into place.

Click

It all falls into place.

You build it lying on its back, step by step, as the manual shows. A turn of the hex key pulls each joint tight.

25Step 25 of 44
Top

Preview renderPose as in the manual (stand-in until the export has it) · render

The finished birch-plywood cart, everything closed.

Here it is

One sheet.
Fine, four.

A birch cart on casters for grey Euro boxes, with two drawers and a door. The boxes slide out like drawers; the plywood stays plain.

  • 25 parts
  • 4 sheets
  • 5 Euro boxes
  • 44 steps

Preview renderRendered from our software's 3D model of this cart. Room and props are staging.How far the drawer and the box slide out is a stand-in.

874 × 620 × 1,138 mm, 4 Euro boxes, 4 drawers, on casters

Render of this exact combination from our software's 3D model.

Make yours

240 ways
to make it yours.

Pick two or three columns, what goes in each and what it stands on. Our software built and checked every one of them in advance.

Columns
Column 1
Column 2
Base

874 × 620 × 1,138 mm4 Euro boxes, 4 drawers, on casters

Render: sheet S04 at dusk, with room left on it beside the back panel and the drawer bottoms.

One more part

There's room on this sheet for one more part.

Sheet S04 still has space. Leave your email and we'll write when Shuplo goes on sale.

Get on the list

Shuplo isn't on sale yet. Leave your email and we'll tell you when it is.

Sheet S04, the back panel and drawer bottoms, as nested · render

Questions

Questions, answered.

Can I buy it now?

Not yet. We're finishing the configurator and the plans. Leave your email and we'll let you know when you can order.

How much will it cost?

We haven't set prices yet. We'll publish them when we launch.

Which Euro containers fit?

Shuplo is designed for containers with a 600 × 400 mm or 400 × 300 mm footprint, measured at the top rim, without a lid. We designed it to the Auer EG 64 and EG 43 series. Before we recommend any box, we will try it on our prototype.

What's in the plan?

A cut list, technical drawings of the whole unit and of every part, a step-by-step assembly manual (Czech and English) and DXF files of the parts. Our software makes all of them from your design.

Can I build it from the plan in my own workshop?

Yes, if your workshop can cut the connector grooves: today's design needs a Lamello Zeta P2 cutter or a CNC router with Lamello P-System tools for them. The drawings and DXF files show every hole and groove, but the assembly manual assumes panels that arrive ready-machined, so it does not explain the milling and drilling. The bottom panel is screwed on with confirmat screws. You need birch plywood, 18 mm for the carcass and the shelves and 9 mm for the back; the plan lists every part and every fitting.

Does it have to be fixed to the wall?

The plan includes wall fixing for every unit taller than 1,200 mm (840 mm for the shallow 420 mm deep version). We recommend fixing any unit to the wall, especially where children are.

Can I sit on the low shoe rack?

Please don't. We haven't load-tested any module for sitting yet.

What is it made of?

Birch plywood: 18 mm for the carcass and shelves, 9 mm for the back. The boxes are standard plastic Euro containers.

What happens to my email?

We send one confirmation email, then only news about Shuplo. We don't sell or share your address, except with the services that send our emails and run this site (Supabase, Resend, Cloudflare). Every email has a one-click unsubscribe link.

Who is behind Shuplo?

Shuplo is a project of Saasup s.r.o. Write to us at info@shuplo.com.